on my Emphaser EAD the relays do not pick up. when i bridge them,amp plays normal sound. Q50,51, are ok what else could. Does anyone know what kind of transistors have in outputs and power supply? I am thinking to buy one with blown outputs and fets. Search among more than user manuals and view them online
|Country:||Bosnia & Herzegovina|
|Published (Last):||2 April 2012|
|PDF File Size:||12.1 Mb|
|ePub File Size:||10.5 Mb|
|Price:||Free* [*Free Regsitration Required]|
Bei allen nachfolgend beschriebenen Installationsschritten muss der Stromkreis des Kraftfahrzeugs unterbrochen sein! The contact point where the eea1800d wire is attached to, must be solid and clean, i. Die Loudnessfunktion ist auch zu deaktivieren.
This control device allows the convenient level adjustment of the bass volume. The higher the subsonic crossover frequency is set, the higher the mechanical power handling of the connected subwoofer system will be. The amp that runs in Slave mode has its control functions deactivated — ALL settings must be done on the Master amp.
Before you attempt to adjust the lowpass crossover frequency, you must set the subsonic highpass filter to its lowest position 10 Hz. Furthermore, it might be necessary ae1800d invert the connection polarity of your subwoofer — and re-adjust the es1800d, if you can not find a proper match with the normal in-phase subwoofer connection.
Die Garantie dieses Produkts bleibt in jedem Fall auf die Reparatur bzw. The applicable fuse value must. Now you can connect the RCA interconnects to the respective outputs of. Before you attempt to adjust the lowpass crossover frequency, you must set the subsonic highpass filter to its lowest position 10 Hz.
The ground power wire must have the same cross-section as the positive power cable. Inspected and approved by: The contact point where the. Slowly increase the input gain control of the channel pair, that drives the subwoofer sby turning the GAIN control clockwise until you can just about hear distorted sounds coming out of wa1800d subwoofer system.
Now switch on your head unit. Important Notice To maximize the performance of this amplifier and your car audio system install, we recommend that you acquaint yourself thoroughly with all capabilities and features of this EMPHASER amplifier.
This phase adjustment can only be emphader by ear, so you will need somebody to help you to obtain best phase match. The amp that runs in Slave mode has its control functions deactivated — ALL settings must be done on the Master amp.
Daarnaast kan empgaser zijn dat uw internetprovider een maximum heeft aan de grootte per email. A good match of the acoustical phase between subwoofer and the system in the front doors will give you the impression of bass sounds coming from a place in front of you.
This setting depends on the dimension and the power handling of the installed subwoofer system. Comments to this Manuals Your Name.
EMPHASER EAD Specifications
It’s a community-based project which helps to repair anything. Please note that – because of possible interference problems with the existing car electrics and electronics – especially the routing of the signal cables and the chassis ground connection will have a ea180d0 impact on the trouble-free noise free! Page of 32 Go. Each RCA line-input pair accepts input voltages from mV to 7V, providing a good match with the line-output levels of almost any head-unit emphasef the market.
Emphaser EA 1800D
A good match of the acoustical phase between subwoofer and the system in the front doors will give you the impression of bass sounds coming from a place in front of you. Stel uw vraag in het forum. ZIP or Postal Code: When baring wires for connection, remove approximately mm of the insulation and after axially twisting the wires, insert the bare ends into the corresponding speaker terminal output on the amplifier.
If the LED lights up red, your installation is wrong! To maximize the performance of this amplifier and your car audio system install, we recommend that you acquaint yourself thoroughly with all capabilities and features of this EMPHASER amplifier.
The low pass level remote control — if installed in your system configuration – should be set at a low position, so there is enough headroom to turn up the bass volume later on. Durch die ausschliessliche Verwendung von hochwertigsten Materialien in der Fertigung, ist die Betriebssicherheit besonders hoch.
Beachten Sie nachfolgende Empfehlungen: Antwoorden worden ook per e-mail naar abonnees gestuurd.
Controleer uw email en volg de aanwijzingen op om uw inschrijving definitief te maken. Exposure to excessive humidity, fluids, sun rays or excessive dirt or dust.